Rocking Slabs Cost Money Every Shift. Here's How One Bottling Plant Fixed Theirs in a Day. Warehouse Floor Stabilizing Project

If you manage a warehouse, distribution center, or plant floor, you know the sound: a forklift rolls across a joint and the slab drops and thumps back into place. Drivers feel it in their backs, loads shift on the forks, and product ends up on the floor. Most facilities treat it as a nuisance until a joint starts to break apart. By then the repair is bigger, slower, and more expensive.
A recent case study from NCFI Geotechnical shows how a Pepsi bottling plant in Nashville dealt with exactly this problem, and why the same approach works on industrial floors here in Arizona.
The Problem: Voids Under the Floor Slab
Large concrete floors are saw-cut into smaller panels shortly after they are poured. Those cuts are control joints, and they are where the trouble starts. Over time, the soil under the panels washes out or settles, and voids open up beneath the edges. When a loaded forklift crosses an unsupported joint, one panel rocks down while the next one stays put.
At the Pepsi plant, that rocking was jarring forklifts, wearing on drivers, and costing the plant in damaged product. Left alone, the panel edges begin to chip and fracture, a condition called joint spalling. Spalling spreads along the joint and can eventually ruin the slab, which turns a joint repair into a slab replacement.
The Solution: Polyurethane Void Fill Through Small Holes
Pepsi brought in Mid-South Concrete Leveling of Milan, Tennessee. Their crew used NCFI's TerraThane geotechnical polyurethane foam to stabilize the joints. The process was simple:
Clean out the joints and remove debris.
Drill 5/8-inch injection holes roughly every three to four feet along the affected joints.
Pump polyurethane void fill foam under the slab to fill the voids and support the panel edges.
The foam expands into the voids, fills them, and cures in place. According to the case study, the material generally reaches about 90 percent of its strength within 15 minutes of injection. As the contractor put it, "It worked great, and quickly so no real downtime for the warehouse."
The Results
The floor was back in service by the time the crew packed up. Pepsi was satisfied enough that it asked the crew to patch roughly 130 feet of cracks in the slabs while they were on site, and the contractor reported getting additional work from the plant afterward.
The contractor chose polyurethane over traditional methods for practical reasons: faster setup, quick cure, very little cleanup, and long-term stability at the joints.
Why This Matters for Arizona Facilities
The Pepsi plant's voids came from erosion under the slab. Arizona floors face their own causes of soil loss and movement:
Expansive clay soils that swell when wet and shrink when dry.
Collapsible desert soils that consolidate once they take on water.
Monsoon runoff, roof drain discharge, and broken irrigation or plumbing lines washing out fill under slab edges.
Heavy, repeated wheel loads from forklifts, pallet jacks, and trucks at dock doors.
Whatever the cause, the result is the same: an unsupported slab edge that rocks, cracks, and eventually spalls. Polyurethane injection addresses the cause (the void) rather than only grinding or patching the surface.
Polyurethane vs. Tearing Out the Slab
For an operating facility, the biggest cost is usually downtime, not materials. Compared with removing and repouring concrete, foam injection offers:
Small 5/8-inch holes instead of demolition.
Floors that can typically return to service the same day.
Lightweight material that adds little load to the soil underneath.
Minimal mess, so work can be phased around production.
Where We Fit In
Southwest Foundation Anchoring is the geotechnical division of Spray Foam Arizona, which has worked with polyurethane foam across Arizona since 2000. Our crew trained with NCFI's geotechnical division, the same manufacturer whose material was used at the Pepsi plant, and we run dedicated geotechnical injection equipment.
We work statewide with facility managers, property managers, engineers, and architects on commercial, industrial, municipal, education, utility, and mining projects, including:
Warehouse and plant floor joint stabilization
Concrete slab lifting and leveling
Void filling under slabs, sidewalks, and loading docks
Foundation and asphalt stabilization
Is Your Floor Rocking?
Warning signs to watch for:
A thump or drop when forklifts cross a joint
Chipped or broken edges along control joints
Uneven joints that catch pallet jack wheels
Pumping, where fine material or water comes up through joints under traffic
Catching voids before spalling starts keeps the repair small. Contact SFA at 520-252-3823 or sprayfoamarizona@gmail.com to schedule a floor assessment.
Project details referenced in this post come from NCFI Geotechnical Case Study 24-003, "Nashville Pepsi Bottling Plant: Rocking Slab Stabilization." The work described was performed by Mid-South Concrete Leveling. Learn more at www.ncfigeo.com.



Comments